Boating in the summer is a fun and exciting experience, to say the least. But when the winter season comes after summer, the boat is kept in a good place and with care for many days.
Since it is not possible to leave the boat under the open sky, the question then is to keep the boat well covered. Many people are very confused, will he leave the boat with a normal cover or shrink wrap it?
And when it comes to wrap, many don’t understand what to do at first. To him it may seem quite obscure and complicated. But believe me, shrink wrap the boat is not a difficult task. If you follow a few steps very well, you can do it yourself in just over an hour.
So let’s take a step-by-step look at how to do it without delay:
What Kind of Materials will be Needed to Shrink Wrap the Boat
Below are some of the tools and materials you will need to do this.
- Strapping
- Buckles
- Heat gun
- Shrink wrap
- Film knife
- Shrink wrap tape
- Wood
- Strap tensioning tool
- 4 – 6 vents
- Super top caps
Step by Step Boat Shrink Wrapping Process
Take a good look at each of the steps below and try to work your way up. If you miss a single step from here, you may need to restart your entire process
Step-1: First, get your boat out of the water with the help of your boat trailer. This work cannot be done in water under any circumstances. When lifting from the water, make sure that the boat is not damaged a bit.
If your boat is small, you can keep the boat on its trailer for the entire winter season. And if it is medium or large size then you can block it.
Step-2: First, place two long wooden posts in the middle of the boat’s deck. Make sure the front post is at least 10 inches above its windshield or at its highest point.
The distance from one post to another is 8 feet. In this case, if the boat is quite large or long, then extra post or pillar should be used. Now put the caps well on top of each pillar.
Step-3:Now tie the polyester strap from the back of the boat to the front on two pillars and tie it very well. Now take two more straps horizontally from one site of the boat to the top of the cap and tie them very tightly.
In this case, do not forget to use the Strap tensioning tool.
Step-4: Now grab the metal rub rail and cut some straps and tie it very tightly. Make sure they are parallel to each other. It is best to keep each strap metal rub rail 8 inches down.
Each strap arranged in parallel should be well knotted to form a loop.
Step-5: At this stage you have to strapping around the boat very well through the loop of each strap. Make sure it is parallel.
The propeller of the boat should be tightened quite well and fastened with the help of this strap. In this case, with the help of strap tensioning tool, it is necessary to make it as strong and tight as possible.
Step-6: Now wrap the boat with high quality shrink wrap. Now this cover has to be fastened quite well with the perimeter band that parallels around the boat. If there is any excess, it should be cut off.
The propeller of the boat should also be wrapped very well in such a way that no part of it can be seen from the outside.
Step-7: Now with the help of a heat gun you have to hold the perimeter band around the boat and attach the shrink wrap well. When doing this, the sharp part of it should be inserted inwards and then heat.
When doing this, you must wear good quality hand gloves.
Step-8: It is better to use a higher tool or ladder and an extension of good quality to heat the surface of the boat. This makes your work much easier and can be completed very quickly.
When heating around the surface of the boat, make sure that you wrap the propeller very well .
Step-9: If you see any cuts or cracks somewhere, cover them well with sheet wrap tape. Then heat it in such a way that no air or water can enter through it.
Step-10: Now put at least four vents on the surface of the boat. Cut in the middle of the vent and put a cap on it so that the air can enter the air without any hindrance but the water cannot enter it under any circumstances.
If your boat is a little big, you can use 6 or more if you want.
Note: If you want to get inside the boat at any time, you can install a zipper door. You can put it where the boat is most convenient for you to enter.
This allows you to get inside your boat without any hindrance and observe its various problems.
Some Tips and Tricks
- If you have shrink wrap for sale, it would be best to use a transparent type of cover. In this case, you can show the buyer the condition of the inside of the boat without any damage to the cover.
- Many do not want to do this because the cost is a little higher than a normal cover. If your boat is brand new then this kind of wrapping would be the wisest thing to do. And if the boat is old, you can only cover it with a normal cover. Although the whole matter is up to you.
Related: Boat Wrap vs Paint: Which is the Best?
Final Thought
Hopefully from the above step-by-step processing you have got a pretty good idea of how to do the boat shrink wrap.
If you still have any questions, please let us know. We will try our best to answer your question as soon as possible.
I have learned several important things through your post. I will also like to express that there can be situation that you will apply for a loan and don’t need a co-signer such as a Federal Student Aid Loan. But when you are getting a borrowing arrangement through a common creditor then you need to be able to have a cosigner ready to help you. The lenders can base their very own decision on a few components but the biggest will be your credit standing. There are some loan companies that will in addition look at your work history and choose based on this but in many instances it will hinge on your credit score.